The reason why the washing tub of the double-tub washing machine does not turn when the tub is spinning is that the brake is not released the Currys discount code.
The rotation of the shaft is difficult, the door cover is not in good contact, the washing machine is leaking, and the rotating motor is checked.
Method/Step
Brake not released
If the holding brake at the bottom of the drying barrel is not released, remove the rear cover and open the door cover of the drying barrel, and then check whether the holding brake is loosened.
If not, then check its door cover connection Check whether the pull wire is loose or broken. If the above situation occurs, you only need to tighten or connect the pull wire so that the brake can be loosened when the door cover is opened.
It is difficult to turn the shaft
If there is a problem that the rotating shaft is difficult to rotate, it may be due to lack of oil or damage. In this case, it is better to ask the maintenance personnel to come to repair it.
Poor contact with the door cover
It is necessary to check whether the switch on the door cover has poor contact or has been bitten off. Remove the three screws at the back of the washing machine and open the operation panel for inspection.
Washing machine leaking
Check whether there is water leakage in the bucket of the washing machine. If there is water leakage, you can replace the sealing ring.
If possible, install a waterproof cover on the motor to prevent water leakage from flowing into the motor and damaging the motor.
Check the rotating motor
Check the rotating motor to see if the motor rotates flexibly. If it is not flexible, it means that the motor is poorly lubricated or the bearing is damaged. It should be disassembled for inspection and filled with lubricating grease.
If the axial clearance of the motor is too large, it should be adjusted by adding shims. If possible, you can use a multimeter to measure whether the coil resistance is normal.
If it is normal, it may be that the starting capacitor is damaged or the capacity is reduced, causing the motor to fail to start or run weakly.
You should replace the starting capacitor with the same capacity. If the coil resistance is abnormal, it means that the coil has a short-circuit fault and the motor should be replaced with a new one Victorian Plumbing Discount Code NHS.
The belt at the bottom of the spin bucket is loose
Check whether the belt at the bottom of the dehydration bucket is loose. If so, tighten the belt or replace the belt again.
Related Experience
- How to identify whether the starting capacitor of the washing machine drying bucket is good or bad
- The washing machine spins and dries the bucket buzzing and cannot turn how to fix it
- Washing machine spins but fails
- What to do if the washing machine does not spin
- How to repair the washing machine
What’s the matter with the double-tub washing machine
The reason why the washing tub of the double-tub washing machine does not turn when the tub is spinning is that the brake is not released, and the rotation of the shaft is difficult.
The door cover is not in good contact, the washing machine is leaking, and the rotating motor is checked.
Detail
Brake not released
If the holding brake at the bottom of the drying barrel is not released, remove the rear cover and open the door cover of the drying barrel, and then check whether the holding brake is loosened.
If not, then check its door cover connection Check whether the pull wire is loose or broken. If the above situation occurs, you only need to tighten or connect the pull wire so that the brake can be released when the door cover is opened.
It is difficult to turn the shaft
If there is a problem that the rotating shaft is difficult to rotate, it may be due to lack of oil or damage. In this case, it is better to ask the maintenance personnel to come to repair it.
Poor contact with the door cover
It is necessary to check whether the switch on the door cover has poor contact or has been bitten off. Remove the three screws at the back of the washing machine and open the operation panel for inspection.
Washing machine leaking
Check whether there is water leakage in the bucket of the washing machine. If there is water leakage, you can replace the sealing ring.
If possible, install a waterproof cover on the motor to prevent water leakage from flowing into the motor and damaging the motor.
Check the rotating motor
Check the rotating motor to see if the motor rotates flexibly. If it is not flexible, it means that the motor is poorly lubricated or the bearing is damaged.
It should be disassembled for inspection and filled with lubricating grease. If the axial clearance of the motor is too large, it should be adjusted by adding shims.
If possible, you can use a multimeter to measure whether the coil resistance is normal. If it is normal, it may be that the starting capacitor is damaged or the capacity is reduced, causing the motor to fail to start or run weakly.
You should replace the starting capacitor with the same capacity. If the coil resistance is abnormal, it means that the coil has a short-circuit fault and the motor should be replaced with a new one.
The belt at the bottom of the spin bucket is loose
Check whether the belt at the bottom of the dehydration bucket is loose. If so, tighten the belt or replace the belt again AO NHS discount.
How to cut a flower pot for a laundry detergent bucket
How to cut the flowerpot for the laundry detergent bucket? So let’s take a look at what the editor shared with you! Hope my experience can help you.
